SI3000 PDF DOWNLOAD

SIC-FS – Silicon Labs | ND DigiKey Electronics · SIC-FS; Silicon Labs; IC VOICE CODEC V/5V 16SOIC; Unit Price $; -. Mounting Type, Surface Mount. Package / Case, SOIC (“, mm Width ). Supplier Device Package, SOIC. Base Part Number, SI Digi-Key Part Number, Manufacturer Part Number, Manufacturer, Packaging, Quantity Available, Unit Price, Minimum Quantity. ND, SIC-FS.

Author: Guzil Togrel
Country: Liechtenstein
Language: English (Spanish)
Genre: Life
Published (Last): 1 January 2016
Pages: 306
PDF File Size: 20.85 Mb
ePub File Size: 20.53 Mb
ISBN: 944-1-75583-165-2
Downloads: 45849
Price: Free* [*Free Regsitration Required]
Uploader: Nigal

Also the Si spec says to bypass unused analog si3000 to ground with a cap. The code will do this in software. Xi3000 is typically somewhat difficult to capture on a scope.

No it is a pulse: It is unnecessary to use the external resistors specified in the Si spec sheet. Oznog Si3000 is no problem just driving the pins from the dsPIC and stop driving them when si3000 is deasserted.

Double check your wiring and make sure you have a 0. Note there are two Master modes, Master Mode 0 will si3000 work.

It requires you to configure COFS to sync with the Si’s bit frame period and there’s sk3000 real reason to need to do that si3000 one more thing to break. So do I need to add some code to playback samples? Forum Themes Si3000 Mobile.

FSample should be somewhere between 8kHzkHz.

Connecting SI3000 and dsPIC33

If you wi3000 seeing a problem please describe it. I use your code to delay after the si3000 and si3000 to leave the si3kReset. Two resitors cost nothing – only taking space on my PCB.

Related Posts  KAFKA BLUE OCTAVO NOTEBOOKS EBOOK DOWNLOAD

The Dane si3000 Hanover Status: Yes, I comment si3000 all the si3000 except di3000 delay. You si3000 remove the entire si3kResetdid you? Can you help me how? I’m using your code entirely. Hi Oznog, Thanks a lot for sharing your work on the si driver. With the DMA controller, the burden on the 33F is still quite low even with all 3 ports in use.

This is yet another reason why putting the Si3000 in Slave s3i000 is simply not a good idea. It’s hardly the only reason si3000. COFG is set to si3000 for 1 word per frame.

The code will pull the pins to the appropriate levels while Si Reset is being asserted.

ITALPRESSE SI – WOOD TEC PEDIA

Nor do I know what would happen inside the SI if the Secondary Frame were not requested and completed before the next Primary Frame is required.

That does essnetial initializations of pin directions and si3000 so excluding this would break si3000 code. Hello Oznog, I decide to make some change to my board si3000 meet si3000 requirements. It would take a huge rewrite to use Slave Mode 2, and personally I think Slave mode is a big mistake.

The SI will automatically give a second FS after the Primary Frame is done but it’s able to complete this Secondary Frame long before the next Primary Frame is scheduled so there is no glitch in the data stream. Your project is very nice and well documented, good job. The code I provided does the initializations, si3000 the Si s will be si3000 as Si3000.

Related Posts  ANALECTAS CONFUCIO DOWNLOAD

Si Voice Codecs | Silicon Labs

There is no known reason for the initialization to fail. Sorry was not clear si3000 me.

IIRC Microchip wrote code putting it in Slave mode, so some people start with the idea that it’s si3000 or more compatible somehow. OK I will double sk3000 the si3000 I made to si3000 software again, looking for pin initialization too. Oznog can you tell me si300 are the “default clock divider values”? The code has everything necessary. TIA and many many thanks for your good job Could you be more specific on how you commented out the reset task?

As soon as possible I will make you informed about develpments. OK I si3000 the value you set. It will help most of us in our si3000, thank you. I allready downloaded you brilliante si3000 and followed your advise with SI as master and fsync generator. I choose si3000 drive the operational mode of the si by resistors and then I comment out your soft-reset.

The code will adapt. Assuming you have an ICD2, use traps. There is no problem just driving the pins from si3000 dsPIC and stop driving them when si3000 is deasserted. Slave mode was not well documented by SILabs and left many questions unanswered. This will scramble the Si registers.